MPLock Identifier
Identify your lock now!
Identify your lock now!
How To Remove And Install A HOPPE HLS9000 Handleset (Swing Door)
This guide shows how to remove and reinstall a HOPPE HLS9000 handleset on a swinging patio or entry door. It’s written for homeowners and installers who need to swap trim, replace a worn lever, or re-seat the handleset after servicing the multipoint lock.
Before You Start
- Work with the door open when possible so you can see alignment and avoid getting locked out.
- If your set uses set screws, use the correct hex key so you don’t strip them.
- Keep all parts in order: interior plate, exterior plate, screws, spindle, cylinder (if keyed).
Video: HOPPE HLS9000 Handleset Removal And Installation
This is the manufacturer video referenced for these steps. If you prefer reading, keep scrolling for the same process in checklist form.
Helpful Diagram (Click To Zoom)
This exploded view helps you visualize the order of parts (backplates, gasket, bushing, lever, cylinder).
Tip: Zoom in to confirm which side gets the screw heads and where the gasket/bushing sit.
Tools You’ll Usually Need
- Phillips screwdriver
- Hex/Allen key for handle set screws (often included with the handleset)
- Small container for screws
How To Remove A HOPPE HLS9000 Handleset
- Open the door and keep it stable (do not let it swing while screws are loose).
- Locate the set screw on the lever (usually on the underside/neck of the handle).
- Loosen the set screw and slide the interior lever off the spindle.
- Repeat for the exterior lever (or support it while you remove the interior side).
- Remove the through-bolts/backplate screws holding the interior and exterior backplates together.
- Carefully pull the backplates away and keep track of any gaskets and bushings.
- If the set is keyed and you are removing the cylinder, remove the cylinder retainer screw on the door edge (typically below the deadbolt) and slide the cylinder out.
Fast Check While It’s Apart
- If the handle felt “wobbly,” inspect the bushing and gasket first.
- If the lever slipped, the set screw may not have been seated fully.
- If keyed operation was rough, confirm the cylinder sits flush and is secured correctly.
How To Install (Or Reinstall) The Handleset
- Press the gaskets onto the inside faces of both backplates so they seal against the door.
- Fit the backplates to the door and start the screws loosely so the plates can still shift for alignment.
- Insert the spindle/shaft through the handle hole and lock gear hub (keep it straight).
- Install the first lever onto the spindle, then tighten the set screw until it is fully seated/flush.
- Install the opposite lever and tighten its set screw the same way.
- If keyed: insert the cylinder until flush and secure it with the edge-of-door cylinder screw.
- Finish by tightening the backplate screws evenly (alternate between screws so the plates pull together square).
After tightening, test operation with the door open: the lever should retract the latch smoothly, and lifting the lever (if your system uses lift-to-lock) should engage the multipoint hardware without binding. If anything feels tight, slightly loosen the backplate screws, re-center the trim, then retighten.
Common Fit Issues (Quick Fixes)
- Lever rubs the backplate: loosen the backplate screws, center the trim, then retighten evenly.
- Lever feels loose: confirm the spindle is fully seated and both set screws are tight.
- Keyed cylinder won’t sit flush: verify the tailpiece orientation and that the retainer screw is not cross-threaded.
Shop Compatible HLS9000 Parts
- HOPPE HLS9000 Accessories (Gaskets, Bushings, Small Parts)
- HOPPE HLS9000 Replacement Lever Handles
- HOPPE HLS9000 Backplates (Interior And Exterior Options)
- HLS9000 Handle Bushings
- Active Euro Cylinders For HLS9000 Trim
Want to learn the terms you’ll see while shopping (like PZ, backset, active vs dummy)? Use the MPLocks glossary as a quick reference: Multipoint Lock Glossary.